 |
| General
Description |
3M
Scotchcal™ High Performace Protective Films are noted for their overall
excellent performance. These rugged, yellowing-resistant urethane
films protect against stone chips, bug damage, abrasion and weathering
whille allowing a vehicle's color brilliance to show through and its
design intent to be maintained. Approved by Automotivve OEMs, these
durable films are flexible, comfortable and easy to apply. PUL 0612
and PUL 1212 are available in rolls of varying widths. |
| Shelf
Life |
It
is recommended that temperatures of 13 degrees C - 32 degrees C (55
degrees RF- 90 degrees F) and 44 percent - 55 percent relative humidity
be maintained in the film storafe location. Film should be used within
one year of purchase. |
| Expected
Effective Performace Characteristics |
Performance
statements are based upon representative experience from testing throughout
the United States; however, actual performance will be determined
by substrate selcetion and preparation, exposure conditions, and maintenance
of the marking. When applied, or when processed and applied according
to 3M recommended procedures, this product will conform to 3M's specifications
for two years following purchase from 3M. |
| Physical
and Chemical characterisitics |
Values
given are typical and are not for use as specifications. If a specification
is desired, a custom specification will be prepared. Any requests
for a specification should be submitteed through your local 3M representative. |
| Performance
Properties |
These
values represent typical data when tested to major OEM urethane specifications
and should not be used for product approval. |
| |
Results |
| Performance
Test and Condition |
PUL
0612 |
PUL
1212 |
| Tensile
MPa (PSI) |
12
(1740) |
12
(1740) |
| Elongation |
200
percent |
200
percent |
| Peel
Adhesion |
| Initial
state - 20 min @ 23 deg. C (73 deg. F) N/m (lb/in) |
600
(3.4) |
600
(3.4) |
| Room
Temp - 72 hrs @ 23 deg. C (73 deg. F) N/m (lb/in) |
700
(4.0) |
700
(4.0) |
| Heat
resistance - 168 hrs @70 deg. C (158 deg. F) N/m (lb/in) |
700(4.0) |
700(4.0) |
| Moisture
resistance - 168 hrs @ 35 deg C (95 deg F) |
700(4.0) |
700(4.0) |
| Thermal
Cycle |
700(4.0) |
700(4.0) |
| Environmental
Simulation |
| Acid
resistance |
Pass |
Pass |
| Fuel
resistance |
Pass |
Pass |
| Heat
resistance - 168 hrs @ 70 deg. C (158 deg F) |
Pass |
Pass |
Moisture
resistqance - 168 hrs @ 35 deg C (95 deg F)
100% R.H. - 2 hrs.@70 deg C (158 deg F) |
Pass |
Pass |
| Thermal
Cycle |
Pass |
Pass |
| Solvent
resistance |
Pass |
Pass |
| Shrinkage |
<.1
percent |
<.1
percent |
| Gravelometer
(SAE J400) |
No
ruptures |
No
ruptures |
|
| Outdoor
Deck Weathering |
Arizona
45 deg. South Facing (unbacked)
- No objectionable gloss loss or change, adhesion loss, film
crackup, or crazing. |
24
months |
Less
than 10 percent gloss loss and no more than 2.5 De color change |
Less
than 10 percent gloss loss and no more than 2.5 De color change |
Florida
5 Deg South Facing (unbacked)
-No objectionable gloss loss or change, adhesion loss, film
crackup, or crazing.
|
24
months |
Less
than 10 percent gloss loss and no more than 2.5 De color change |
Less
than 10 percent gloss loss and no more than 2.5 De color change |
|
| Product
Characteristics |
Adhesive
Liner Max Service temp
|
Acrylic
PSA White - Bleached paper with release coating Film softens
above 67 deg C (150 deg F)
|
|
| Application |
For
detailed information on application of 3M™ Scotchcal™ High Performace
Paint Protective Film, see Instruction Bulletin 2-18. For best results,
apply the film to a clean substrate at temperatures between 13 deg
C - 32 deg C (55 deg F - 90 deg F) |
